united chemi-con, inc. 9801 w. higgins road, rosemont, il 60018 tel 847-696-2000 fax 847-696-9278 www.chemi-con.com 63 mfbp surface mount- 85 c mf bp series the mfbp series are the bi-polar versions of the mf series. these surface mount capacitors are designed for use in circuits which have a reversed or unknown polarity. please note that these capacitors should not be used in applications in which the specified ripple current ratings are exceeded. the mfbp series capacitors were developed to withstand hcfc cleaning agents for five minutes by ultrasonic, vapor or immersion. this solvent proof design allows all circuit board components to be cleaned together, at the same time, without resorting to more expensive epoxy end-sealed capacitors. refer to the mini-glossary for recommended cleaning conditions. surface mount bi-polar low profile horizontal chip solvent proof 85 c maximum temperature actual size surface mount lead terminals. capacitance range: 0.1 to 22f. voltage range: 4 to 50vdc. operating temperature range: 40 cto 85 c. leakage current: 0.05cv or 10a, whichever is greater, after 2 minutes at 20 c. standard capacitance tolerance: 20% nominal case size (h l): 3.5 6.3mm to 4.5 8.3mm. rated lifetime: 2,000 hours at 85 c. summary of specifications
united chemi-con, inc. 9801 w. higgins road, rosemont, il 60018 tel 847-696-2000 fax 847-696-9278 www.chemi-con.com 64 mfbp series mfbp surface mount- 85 c mfbp specifications item operating temperature range 40 to 85 c rated voltage range 4 to 50vdc capacitance range 0.1 to 22 f capacitance tolerance 20% ( m ) at 20 c, 120hz leakage current i 0.05cv or 10 a, whichever is greater, after 2 minutes at 20 c. where i = leakage current ( a ), c = nominal capacitance ( f ) and v = rated voltage ( v ) dissipation factor ( tan )at 20 c, 120hz load life others the following specifications shall be satisfied when the capacitors are restored to 20 c after subjecting them to the dc rated voltage for 2,000 hours at 85 c. polarization shall be reversed every 250 hours. the sum of dc voltage and peak ac voltage must not exceed the full rated voltage of the capacitors. capacitance change: size b6 & c6 : 25% of the initial measured value size d6 & d8 : 20% of the initial measured value tan (df) : 200% of the initial specified value leakage current : initial specified value shelf life the following specifications shall be satisfied when the capacitors are restored to 20 c after exposing them for 500 hours at 85 c without voltage applied. the rated voltage shall be applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than 48 hours before the measurements. capacitance change: 15% of the initial measured value tan (df) : 150% of the initial specified value leakage current : initial specified value characteristics satisfies characteristic w of jis c5141 low temperature characteristics at 120hz, impedance ( z ) ratio between the 25 c or 40 c value and 20 c value shall not exceed the values given below. 50 2 2 4 3 35 2 2 4 3 25 2 2 5 4 16 3 2 7 6 10 4 3 9 8 4 9 7 17 15 6.3 6 4 12 10 size b6 & c6 size d6 & d8 size b6 & c6 size d6 & d8 z( 25 c) /z( 20 c) z( 40 c) /z( 20 c) rated voltage ( v ) 50 0.22 0.20 rated voltage ( v ) size b6 & c6 size d6 & d8 6.3 0.35 0.32 4 0.50 0.45 10 0.30 0.26 16 0.26 0.24 25 0.24 0.22 35 0.22 0.20 lead length: tp is for standard taping. case code: see case sizes in tables. capacitance tolerance: m = 20% capacitance value: expressed in microfarads. the first two digits are significant figures, and the third digit indicates the number of zeros for capacitance of 100 f or more. r indicates the decimal point for capacitance less than 100 f (e.g. r10 = .10 f; 1r0 = 1.0 f; 10r = 10 f; 101 = 100 f; 102 = 1,000 f; 103 = 10,000 f). lead configuration: fc = horizontal chip lead terminals. dc rated voltage: expressed in volts (e.g. 4 = 4wvdc). series name: indicates basic capacitor design. part numbering system for mfbp series when ordering, always specify complete catalog number for mfbp series. mfbp 4 fc 10r m c6 tp
mfbp series united chemi-con, inc. 9801 w. higgins road, rosemont, il 60018 tel 847-696-2000 fax 847-696-9278 www.chemi-con.com 65 mfbp surface mount- 85 c standard voltage ratings - surface mount rated voltage (wvdc) capacitance (f) catalog part number nominal case size* h l ( mm ) maximum ripple current ( ma rms) at 85 c, 120hz maximum esr ( ? ) at 20 c, 120hz case code 6.8 mfbp4fc6r8mb6tp 3.5 6.3 b6 121.875 7.2 10 mfbp4fc10rmc6tp 4 6.3 c6 82.875 9.5 15 mfbp4fc15rmd6tp 4.5 6.3 d6 49.725 15 22 mfbp4fc22rmd8tp 4.5 8.3 d8 33.903 19 4 volts 5 volts surge 2.2 mfbp16fc2r2mb6tp 3.5 6.3 b6 195.886 6.1 3.3 mfbp16fc3r3mc6tp 4 6.3 c6 130.591 8.2 4.7 mfbp16fc4r7md6tp 4.5 6.3 d6 84.638 12 6.8 mfbp16fc6r8md8tp 4.5 8.3 d8 58.5 15 16 volts 20 volts surge 1.5 mfbp25fc1r5mb6tp 3.5 6.3 b6 265.2 5.3 2.2 mfbp25fc2r2mc6tp 4 6.3 c6 180.818 7 3.3 mfbp25fc3r3md6tp 4.5 6.3 d6 110.5 10 4.7 mfbp25fc4r7md8tp 4.5 8.3 d8 77.585 13.3 25 volts 32 volts surge 3.3 mfbp10fc3r3mb6tp 3.5 6.3 b6 150.682 6.9 4.7 mfbp10fc4r7mc6tp 4 6.3 c6 105.798 9 6.8 mfbp10fc6r8md6tp 4.5 6.3 d6 63.375 13 10 mfbp10fc10rmd8tp 4.5 8.3 d8 43.095 16 10 volts 13 volts surge 3.3 mfbp6.3fc3r3mb6tp 3.5 6.3 b6 175.795 6.2 4.7 mfbp6.3fc4r7mb6tp 3.5 6.3 b6 123.431 7.4 6.8 mfbp6.3fc6r8mc6tp 4 6.3 c6 85.313 9.8 10 mfbp6.3fc10rmd6tp 4.5 6.3 d6 53.04 14 15 mfbp6.3fc15rmd8tp 4.5 8.3 d8 35.36 18 6.3 volts 8 volts surge * refer to diagrams for detailed case size dimensions. horizontal chip lead terminals fd type (special order) recommended solder pad on pc board unit: mm diagram of dimensions fc type (standard) without dummy terminal ( fc ) with dummy terminal ( fd ) * for mechanical support, copper paste coated and dried. figure 1 figure 3 figure 4 figure 2 case code b6 c6 d6 d8 l 0.2 max. 6.3 6.3 6.3 8.3 w 0.2 max. 3.6 4.1 4.6 4.6 p 0.3 3.0 3.5 4.0 4.0 h 0.2 max. 3.5 4.0 4.5 4.5 figure 1 & 2 case dimensions case code b6 c6 d6 d8 w 1 3.6 4.1 4.6 4.6 a 1.0 1.3 1.5 1.5 b 1.2 1.2 1.2 2.2 c 1.65 1.65 1.65 2.65 figure 3 & 4 solder pad dimensions h w p w 1 1.1 a b 1.1 a 2.4 location of capacitor location of capacitor 1.1 a b c 1.1 a 2.4 1. 5 solder pad l 1. 5 0.2 0.2 max. marking 1. 5 0.2 dummy terminal * for tape and reel packaging and reflow soldering conditions, refer to the beginning of the surface mount section.
united chemi-con, inc. 9801 w. higgins road, rosemont, il 60018 tel 847-696-2000 fax 847-696-9278 www.chemi-con.com 66 mfbp series mfbp surface mount- 85 c 0.1 mfbp50fcr10mb6tp 3.5 6.3 b6 3,646.5 1.3 0.15 mfbp50fcr15mb6tp 3.5 6.3 b6 2,431.0 1.9 0.22 mfbp50fcr22mb6tp 3.5 6.3 b6 1,657.5 2.3 0.33 mfbp50fcr33mb6tp 3.5 6.3 b6 1,105.0 2.8 0.47 mfbp50fcr47mb6tp 3.5 6.3 b6 775.851 3.3 0.68 mfbp50fcr68mb6tp 3.5 6.3 b6 536.25 4.0 1.0 mfbp50fc1r0mc6tp 4 6.3 c6 364.65 5.3 1.5 mfbp50fc1r5md6tp 4.5 6.3 d6 221.0 7.5 2.2 mfbp50fc2r2md8tp 4.5 8.3 d8 150.682 10 50 volts 63 volts surge standard voltage ratings - surface mount rated voltage (wvdc) capacitance (f) catalog part number nominal case size* h l ( mm ) maximum ripple current ( ma rms) at 85 c, 120hz maximum esr ( ? ) at 20 c, 120hz case code 1.0 mfbp35fc1r0mb6tp 3.5 6.3 b6 364.65 4.6 1.5 mfbp35fc1r5mc6tp 4 6.3 c6 243.1 6.1 2.2 mfbp35fc2r2md6tp 4.5 6.3 d6 150.682 9.1 3.3 mfbp35fc3r3md8tp 4.5 8.3 d8 100.455 12 35 volts 44 volts surge * refer to diagrams for detailed case size dimensions.
|
